Pete's Pillars Ruger 10/22 Viton & Stainless Bolt Buffer

Price:

$ 5.74


MDT Rifle Chassis Vertical Buttpad Adjustment Base 107097-BLK
MDT Rifle Chassis Vertical Buttpad Adjustment Base 107097-BLK
$ 99.95
$ 99.95
SLING SWIVEL Accessory Rail 7953M
SLING SWIVEL Accessory Rail 7953M
$ 44.99
$ 44.99

Pete's Pillars Ruger 10/22 Viton & Stainless Bolt Buffer

https://www.petespillars.com/web/image/product.template/18080/image_1920?unique=fec707a
(0 review)

$ 5.74 5.74 USD $ 5.74

$ 5.74

Not Available For Sale

IN STOCK
FREE Shipping*  Most Orders Ship Same Day!*

  • Brand
  • Gun Platform
  • Type

This combination does not exist.



PETE'S PILLARS | RUGER 10/22 | VITON BOLT BUFFER | SINGLE | MADE IN USA

Your Bolt Is Hammering Aluminum.

Every shot, the bolt of your Ruger 10/22 runs back and stops against a steel cross pin pressed into an aluminum receiver. The Pete's Pillars 80110 Viton bolt buffer replaces that steel with a Viton fluoroelastomer body on a stainless core, so the bolt stops against something designed to absorb the hit. One buffer, machined and assembled in the USA.

This is the single buffer. It is the smallest change you can make to a 10/22 and one of the few that every single round goes through. Punch out the factory pin, drop this in, done — no fitting, no gunsmith, no permanent modification. If you are building more than one rifle or you want a spare in the range bag, the 2-pack and 3-pack are the same part at a better per-unit price.

Viton, Not Whatever Rubber Was Cheapest.

Viton is a fluoroelastomer. It holds its shape and its resilience around the solvents, oils and heat that live inside a rimfire action, where cheaper rubber swells, goes gummy or hardens and cracks. Paired with a stainless core, you get a buffer that stays a buffer instead of turning into a smear of residue after a season of bulk ammo.

Made With Genuine Viton fluoroelastomer

Genuine Material

Made With Genuine Viton Fluoroelastomer.

Not a generic black O-ring sold as one. Viton is a registered trademark of its manufacturer, and we use the real material because the difference only shows up after a season of solvents, oils and heat — which is exactly when you do not want to find out you bought the cheap version.

What It Actually Changes.

Two things, and we will not pretend otherwise. The action sounds and feels softer at the end of bolt travel, because an elastomer absorbs impact that steel simply transmits. And the repeated metal-on-metal contact at the stop point goes away. It is a wear item by design — it takes the beating so your receiver does not, and when it is done you replace a few dollars of buffer rather than living with a peened receiver.

Stock Ruger, KIDD or Volquartsen. Same Job.

A buffer is not brand-specific. If you are running a KIDD CNC bolt and receiver, a Volquartsen competition bolt, or a bone-stock Ruger action, the bolt still stops in the same place and still needs something there to stop against. Builders who spend real money on a KIDD or Volquartsen bolt are exactly the people who should not be leaving the factory steel pin in place.

Pair It With

Three of our own parts that belong on the bench the same afternoon. The P7643 kit pairs these buffers with stainless trigger assembly cross pins, which is the other set of factory pins worth replacing while the action is open.

Upgrade the Action

Triggers, Bolts & Charging Handles

The parts the buffer works alongside. A better bolt and trigger change how the rifle runs; the buffer decides what that bolt stops against.

All 10/22 Parts →

Finish the Build

Stocks, Chassis & Magazines

Where a bull-barrel 10/22 ends up living, plus factory magazines. Field Stock and Oryx are distinct 10/22 inlets, not universal replacements.

All 10/22 Parts →

Need a Different Pack Size?

Volquartsen HP Action Kit Plus for Ruger 10/22

The Next Level

Rebuild the Whole Action at Once.

A buffer fixes where the bolt stops. The Volquartsen HP Action Kit Plus fixes what the bolt does on the way there. It is the complete action package rather than one part at a time, and it is the honest answer for anyone who has already swapped a trigger, a bolt and a barrel separately and is still chasing the feel. Start here instead of working up to it in six orders.

See the HP Action Kit →

We Make This Part Ourselves.

Pete's Pillars machines pillars, buffers, screws and small action parts in Michigan, and carries the brands we would put on our own rifles for everything else. If you are working through a 10/22 build, our Ruger 10/22 parts and upgrades page collects it in one place. We also do custom Cerakote in house, so if you want the chassis and barrel to match, tell us what you are building.

Did You Know? Pete's Pillars Sells More Than Pillars.

We make practical USA-made parts and stock the brands that finish the rifle.

Key Specifications

MPN: P60110-BLK

Manufacturer: Pete's Pillars

Fitment: Ruger 10/22 pattern actions, including KIDD and Volquartsen builds

Quantity: One buffer

Buffer Material: Viton fluoroelastomer

Core: Stainless steel

Replaces: Factory steel recoil buffer cross pin

Installation: Drop-in, no fitting or permanent modification

Service Life: Wear item; inspect at cleaning and replace as needed

Made in USA

Frequently Asked Questions

Fitment, material, install and how this part fits a 10/22 build.

What does a bolt buffer actually do on a Ruger 10/22?

At the end of its travel the bolt stops against a cross pin at the rear of the receiver. From the factory that pin is steel, and the contact is metal on metal, several thousand times over the life of the rifle. A Viton buffer puts an elastomer in that path, so the impact is absorbed instead of transmitted. The practical result is a softer, quieter stop and no repeated steel-on-aluminum hammering at the stop point.

Will this work with a KIDD or Volquartsen bolt?

Yes. KIDD and Volquartsen complete bolts run in the same receiver and stop in the same place, so the buffer location does not change. If anything it matters more on those builds: a machined competition bolt is heavier and faster than a factory bolt, and it is worth giving it something better than a steel pin to land on. Check the instructions for any bolt that ships with its own buffer so you are not doubling up.

Which pack should I buy: one, two or three?

Buy by how many 10/22s you own and how often you shoot. The P60110-BLK single is a straight replacement for one rifle. The P80120-BLK 2-pack covers most people: one installed, one in the range bag. The P80130-BLK 3-pack is the lowest cost per buffer and makes sense for several rifles, a club bench or high-volume match use.

Is installation hard? Do I need a gunsmith?

No. The buffer goes where the factory cross pin sits, so it is a drop-in swap with a punch and a few minutes, no fitting and no permanent modification to the rifle. Clear the rifle and verify it is unloaded before starting, and follow the disassembly sequence in your owner's manual. If you are already replacing a charging handle or recoil rod, do the buffer at the same time.

Why Viton instead of standard rubber?

Viton is a fluoroelastomer, and the reason it is used here is chemical and thermal stability. The inside of a rimfire action sees powder residue, bore solvents, oils and heat, and ordinary rubber responds to that by swelling, going gummy or hardening and cracking. Viton holds its shape and its resilience in that environment, which is why it is worth the material cost on a part this small.

How often should I replace it?

Treat it as a wear item, which is the whole point of fitting one. Look at it whenever you have the action apart for cleaning and replace it when it shows flattening, splitting or hardening. Volume shooters replace them more often than someone who shoots a few hundred rounds a year, which is exactly why we sell the 2-pack and 3-pack.

Is installation included? And what is the trick to it?

Installation is not included, but here is how to do it without fighting it. Do not try to push the buffer straight in. Start one side of the buffer through, then work the second side from the inside out. Once the buffer is seated in its location, push the stainless pin in through it. Trying to force it in as one motion is what makes people think the part is oversized. Clear the rifle and confirm it is unloaded before you start.

Will the stainless pin rust or become magnetic?

Stainless is a family of alloys, not one material, and the alloy decides the answer. Austenitic grades, the 300 series, carry higher chromium and nickel and give the best corrosion resistance; in the annealed state they are essentially non-magnetic, but machining and cold working can leave them slightly magnetic, which is normal and is not a sign you received the wrong part. Martensitic and ferritic grades, the 400 series, are magnetic by nature and trade some corrosion resistance for hardness. In every case stainless is corrosion resistant, not corrosion proof — it works by holding a chromium oxide layer, and that layer does its best work on a clean, lightly oiled part. Wipe it down and put a light film of oil on it when you clean the rifle and, under normal use, it will not rust.

The buffers in my pack are not all exactly the same size. Is that a defect?

No, and it is worth explaining why. The buffer is an extruded elastomer part, not a machined metal one. Extrusion pushes material through a die and cuts it to length, and the material relaxes afterward, so dimensional tolerance is naturally wider than you would see on a turned stainless pin. Small differences in length or diameter between buffers in the same pack, or between orders, are normal to the process and do not change how the part does its job. What matters is that it seats in the buffer location and stops the bolt. If one genuinely will not seat, tell us and we will make it right.

Will a bolt buffer make my rifle more accurate?

No, and we are not going to claim it will. A buffer changes how the action feels and protects the receiver from repeated impact; it does not change how the barrel shoots. Accuracy on a 10/22 comes from the barrel, the way it is clamped to the receiver, and the stock or chassis holding it. Our Premium Upgrade Kit addresses that interface, and a better trigger changes how well you can shoot whatever the barrel will do.

Does it fit the Ruger Charger or the 10/22 Takedown?

These are built for the Ruger 10/22 pattern action. The Charger and the Takedown share that action design, but packaging and parts vary by model and year, so verify the buffer location on your specific rifle before ordering. Send us your model and we will tell you straight.

Machined and assembled by Pete's Pillars in Michigan.

Small Change. Big Impact. Pete's Pillars.

*

Brand Pete's Pillars
Gun Platform 10/22
Type Action Parts