TANDEMKROSS SPARTAN SKELETONIZED CHARGING HANDLE | RUGER 10/22 | SILVER
A Bigger Grip in a Clean Silver Finish.
The TandemKross Spartan TK18N0121SLV1 replaces the small factory charging handle on your Ruger 10/22 with a long, curved, skeletonized handle in a clean silver finish. It rides on a stainless steel guide rod, installs without permanent modification and fits standard 10/22 rifles, 10/22 Takedowns and 22 Charger pistols.
The factory 10/22 charging handle is a small knob that gets harder to work with cold hands, gloves or an optic sitting low over the receiver. The Spartan gives you roughly twice the handle to grab, so charging the rifle and clearing a malfunction is quicker and more positive. It's one of the most popular first upgrades on the 10/22, and it's a fast way to make a factory rifle feel like a custom build. Use it for: rimfire steel challenge, NRL22, plinking, small game and any 10/22 or 22 Charger build that deserves a better grip.
Built for Leverage.
The Spartan's elongated, curved profile puts more surface under your finger and more leverage behind every pull. The skeletonized cuts keep it light, and the stainless steel guide rod and recoil spring are retained on the assembly, so the spring stays put during cleaning and you can swap spring weights to tune for your ammunition. Installation uses no special tools and makes no permanent changes to your rifle. Made in the USA by TandemKross.
Why Silver?
Silver gives the Spartan a bright, machined look that reads as a deliberate upgrade without shouting. It ties in with stainless barrels and silver hardware, and it makes a sharp two-tone contrast against a black receiver. Pair it with the Volquartsen TG2000 Silver Trigger Guard for a matched silver build. Want more contrast or a stealthier look? The Spartan also comes in Red and Black.
Building a KIDD- or Volquartsen-Grade 10/22?
KIDD and Volquartsen set the bar for competition 10/22s, and a lot of serious builds pair a KIDD single-stage trigger or receiver parts with TandemKross controls. We stock a deep selection of Volquartsen components plus KIDD parts like the KIDD Rear Tang. Whichever way you build, our stainless V-Block Screws and take-down screws are machined to fit KIDD and Volquartsen setups. Ready for more barrel? The Volquartsen UltraLite 16.5″ VCULB-28 keeps the rifle light, and the Volquartsen 18.5″ .920 Match Bull Barrel VC10NC-28 is built for the bench (confirm your stock's barrel channel clearance).
Pair It With
P7643-BLK Buffer & Pin KitViton buffer plus stainless trigger pins
TandemKross Krossfire BoltCNC-machined, PVD-coated 10/22 bolt
Midwest Industries 10/22 RailSolid Picatinny base for any optic
Bull-Barrel Ready
Stocks & Chassis for Your 10/22
Field-ready and competition-proven homes for a bull barrel. Confirm barrel channel clearance on each listing.
MDTField Stock Ruger 10/22Lightweight, adjustable chassis-based stock.Shop Now →
KRGBravo 10/22 ChassisAdjustable, rugged and proven on the match line.Shop Now →
MDTOryx Sportsman 10/22Proven, affordable aluminum chassis.Shop Now →
MDTOryx 10/22 – M81 WoodlandCustom Cerakote by Pete's Pillars.Shop Now →
Upgrade the Rest
Complete Your 10/22
Buffers, screws, bolts, triggers, rails and more, ready to ship.
Made in USAPete's PillarsViton Stainless Bolt BuffersQuieter, smoother cycling. 3-pack.Shop Now →
Made in USAPete's PillarsViton Buffer & Trigger Pin KitBuffers plus stainless trigger assembly pins.Shop Now →
Made in USAPete's PillarsStainless V-Block ScrewsCustom machined for KIDD and Volquartsen builds.Shop Now →
TandemKrossKrossfire CNC BoltCNC-machined, PVD-coated bolt.Shop Now →
TandemKrossManticore Trigger AssemblyComplete drop-in trigger upgrade.Shop Now →
Midwest Industries10/22 Picatinny Scope RailSolid Picatinny base for any optic.Shop Now →
VolquartsenVC10FE Bolt Tune-Up KitExtractor and firing pin upgrade.Shop Now →
VolquartsenTG2000 Trigger GuardDrop-in, 2 lb competition trigger.Shop Now →
The Next Level
Match the Silver. Upgrade the Trigger.
- Volquartsen TG2000 billet-aluminum trigger guard assembly
- Rapid Release magazine release for faster mag changes
- Silver finish matches the Spartan for a clean, matched build
Shopping a KIDD or TandemKross single-stage trigger? The TG2000 is the drop-in Volquartsen alternative. Prefer black? See the TG2000 Black VCTP-1-B-10.
Did You Know?
Pete's Pillars Sells More Than Pillars.
From centerfire chassis to optics and reloading, outfit every rifle in the safe in one place.
Optics & Mounts
Bipods & Magazines
Product Specifications
Manufacturer: TandemKross
Model: Spartan Skeletonized Charging Handle
MPN: TK18N0121SLV1 (also listed as 3018N0121CRM1)
Finish: Silver
Design: Extended Curved, Skeletonized Handle
Includes: Charging Handle with Stainless Steel Guide Rod and Recoil Spring
Fits: Standard Ruger 10/22 Rifles, 10/22 Takedown and Takedown Lite, 22 Charger, Charger Takedown and Charger Lite
Installation: Replaces Factory Charging Handle Assembly, No Permanent Modification
Manufactured: USA
Frequently Asked Questions
Fitment, installation, finish and completing your Ruger 10/22.
Will it fit my rifle?
The Spartan is built for standard Ruger 10/22 rifles (Carbine, Sporter, Compact, Tactical and Target), the 10/22 Takedown and Takedown Lite, and the 22 Charger, Charger Takedown and Charger Lite. If your rifle runs an aftermarket bolt or receiver, such as KIDD, check fit and spring weight with your build.
Is installation difficult?
No. The Spartan replaces your factory charging handle assembly during normal 10/22 disassembly. No special tools and no permanent modification to the rifle.
Does it come with a guide rod and spring?
Yes. It includes a stainless steel guide rod and recoil spring retained on the assembly. It can be taken apart for cleaning or to swap spring weights for your ammunition.
What does the silver finish look like, and what pairs with it?
It's a bright silver finish that complements stainless barrels and silver hardware and stands out against a black receiver. For a matched build, pair it with the Volquartsen TG2000 Silver Trigger Guard. Want a different look? The Spartan also comes in Red and Black.
Will it help with a scope or red dot mounted?
Yes. With an optic sitting low over the receiver, the small factory knob can be hard to reach. The Spartan's longer, curved handle gives you more to grab, with or without gloves.
What else should I upgrade on my 10/22?
Start with our P7643-BLK Buffer & Trigger Pin Kit and Stainless V-Block Screws, add a Midwest Industries Picatinny Rail, then step up the trigger with a Volquartsen TG2000.
Does Pete's Pillars sell more than 10/22 parts?
Yes. We make CZ 457 parts and pillar bedding, and we carry centerfire chassis from MDT, XLR and Grey Birch, Lilja and L3i barrels, optics and mounts, reloading gear like the Area 419 ZERO press, and Ruger 10/22 and Mark IV upgrades from Volquartsen and KIDD.
Small Change. Big Impact. Pete's Pillars.
TANDEMKROSS SPARTAN SKELETONIZED CHARGING HANDLE | RUGER 10/22 | SILVER
A Bigger Grip in a Clean Silver Finish.
The TandemKross Spartan TK18N0121SLV1 replaces the small factory charging handle on your Ruger 10/22 with a long, curved, skeletonized handle in a clean silver finish. It rides on a stainless steel guide rod, installs without permanent modification and fits standard 10/22 rifles, 10/22 Takedowns and 22 Charger pistols.
The factory 10/22 charging handle is a small knob that gets harder to work with cold hands, gloves or an optic sitting low over the receiver. The Spartan gives you roughly twice the handle to grab, so charging the rifle and clearing a malfunction is quicker and more positive. It's one of the most popular first upgrades on the 10/22, and it's a fast way to make a factory rifle feel like a custom build. Use it for: rimfire steel challenge, NRL22, plinking, small game and any 10/22 or 22 Charger build that deserves a better grip.
Built for Leverage.
The Spartan's elongated, curved profile puts more surface under your finger and more leverage behind every pull. The skeletonized cuts keep it light, and the stainless steel guide rod and recoil spring are retained on the assembly, so the spring stays put during cleaning and you can swap spring weights to tune for your ammunition. Installation uses no special tools and makes no permanent changes to your rifle. Made in the USA by TandemKross.
Why Silver?
Silver gives the Spartan a bright, machined look that reads as a deliberate upgrade without shouting. It ties in with stainless barrels and silver hardware, and it makes a sharp two-tone contrast against a black receiver. Pair it with the Volquartsen TG2000 Silver Trigger Guard for a matched silver build. Want more contrast or a stealthier look? The Spartan also comes in Red and Black.
Building a KIDD- or Volquartsen-Grade 10/22?
KIDD and Volquartsen set the bar for competition 10/22s, and a lot of serious builds pair a KIDD single-stage trigger or receiver parts with TandemKross controls. We stock a deep selection of Volquartsen components plus KIDD parts like the KIDD Rear Tang. Whichever way you build, our stainless V-Block Screws and take-down screws are machined to fit KIDD and Volquartsen setups. Ready for more barrel? The Volquartsen UltraLite 16.5″ VCULB-28 keeps the rifle light, and the Volquartsen 18.5″ .920 Match Bull Barrel VC10NC-28 is built for the bench (confirm your stock's barrel channel clearance).
Pair It With
P7643-BLK Buffer & Pin KitViton buffer plus stainless trigger pins
TandemKross Krossfire BoltCNC-machined, PVD-coated 10/22 bolt
Midwest Industries 10/22 RailSolid Picatinny base for any optic
Bull-Barrel Ready
Stocks & Chassis for Your 10/22
Field-ready and competition-proven homes for a bull barrel. Confirm barrel channel clearance on each listing.
MDTField Stock Ruger 10/22Lightweight, adjustable chassis-based stock.Shop Now →
KRGBravo 10/22 ChassisAdjustable, rugged and proven on the match line.Shop Now →
MDTOryx Sportsman 10/22Proven, affordable aluminum chassis.Shop Now →
MDTOryx 10/22 – M81 WoodlandCustom Cerakote by Pete's Pillars.Shop Now →
Upgrade the Rest
Complete Your 10/22
Buffers, screws, bolts, triggers, rails and more, ready to ship.
Made in USAPete's PillarsViton Stainless Bolt BuffersQuieter, smoother cycling. 3-pack.Shop Now →
Made in USAPete's PillarsViton Buffer & Trigger Pin KitBuffers plus stainless trigger assembly pins.Shop Now →
Made in USAPete's PillarsStainless V-Block ScrewsCustom machined for KIDD and Volquartsen builds.Shop Now →
TandemKrossKrossfire CNC BoltCNC-machined, PVD-coated bolt.Shop Now →
TandemKrossManticore Trigger AssemblyComplete drop-in trigger upgrade.Shop Now →
Midwest Industries10/22 Picatinny Scope RailSolid Picatinny base for any optic.Shop Now →
VolquartsenVC10FE Bolt Tune-Up KitExtractor and firing pin upgrade.Shop Now →
VolquartsenTG2000 Trigger GuardDrop-in, 2 lb competition trigger.Shop Now →
The Next Level
Match the Silver. Upgrade the Trigger.
- Volquartsen TG2000 billet-aluminum trigger guard assembly
- Rapid Release magazine release for faster mag changes
- Silver finish matches the Spartan for a clean, matched build
Shopping a KIDD or TandemKross single-stage trigger? The TG2000 is the drop-in Volquartsen alternative. Prefer black? See the TG2000 Black VCTP-1-B-10.
Did You Know?
Pete's Pillars Sells More Than Pillars.
From centerfire chassis to optics and reloading, outfit every rifle in the safe in one place.
Optics & Mounts
Bipods & Magazines
Product Specifications
Manufacturer: TandemKross
Model: Spartan Skeletonized Charging Handle
MPN: TK18N0121SLV1 (also listed as 3018N0121CRM1)
Finish: Silver
Design: Extended Curved, Skeletonized Handle
Includes: Charging Handle with Stainless Steel Guide Rod and Recoil Spring
Fits: Standard Ruger 10/22 Rifles, 10/22 Takedown and Takedown Lite, 22 Charger, Charger Takedown and Charger Lite
Installation: Replaces Factory Charging Handle Assembly, No Permanent Modification
Manufactured: USA
Frequently Asked Questions
Fitment, installation, finish and completing your Ruger 10/22.
Will it fit my rifle?
The Spartan is built for standard Ruger 10/22 rifles (Carbine, Sporter, Compact, Tactical and Target), the 10/22 Takedown and Takedown Lite, and the 22 Charger, Charger Takedown and Charger Lite. If your rifle runs an aftermarket bolt or receiver, such as KIDD, check fit and spring weight with your build.
Is installation difficult?
No. The Spartan replaces your factory charging handle assembly during normal 10/22 disassembly. No special tools and no permanent modification to the rifle.
Does it come with a guide rod and spring?
Yes. It includes a stainless steel guide rod and recoil spring retained on the assembly. It can be taken apart for cleaning or to swap spring weights for your ammunition.
What does the silver finish look like, and what pairs with it?
It's a bright silver finish that complements stainless barrels and silver hardware and stands out against a black receiver. For a matched build, pair it with the Volquartsen TG2000 Silver Trigger Guard. Want a different look? The Spartan also comes in Red and Black.
Will it help with a scope or red dot mounted?
Yes. With an optic sitting low over the receiver, the small factory knob can be hard to reach. The Spartan's longer, curved handle gives you more to grab, with or without gloves.
What else should I upgrade on my 10/22?
Start with our P7643-BLK Buffer & Trigger Pin Kit and Stainless V-Block Screws, add a Midwest Industries Picatinny Rail, then step up the trigger with a Volquartsen TG2000.
Does Pete's Pillars sell more than 10/22 parts?
Yes. We make CZ 457 parts and pillar bedding, and we carry centerfire chassis from MDT, XLR and Grey Birch, Lilja and L3i barrels, optics and mounts, reloading gear like the Area 419 ZERO press, and Ruger 10/22 and Mark IV upgrades from Volquartsen and KIDD.
Small Change. Big Impact. Pete's Pillars.
| Brand | TandemKross |
| Gun Platform | 10/22 |
| Type | Bolt Parts |